Introduction: Lawn Mower Courser Connection Hack

My wife had trouble with the connector for the rechargeable battery for our lawn mower, she wasn't able to easily disconnection it so it defeated the purpose of having an easy to start lawn lawn mower.

I found a male to female DC extension for $3 at a localized electronics store that I put-upon to ward-heeler in a quick connect so now my wife can easily disconnect the lawn mower whenever she wants to mow the lawn instead of having to wait for me to come home to disconnect it.

The equivalent part connected Amazon would be something like this:

5.5 x 2.1mm DC Power Plug to Socket

or cheaper on eBay if you'atomic number 75 prepared to wait:

1M Superpowe Direct current 5.5x2.1mm Feminine to Male Extension Cord

The key is to find a cable where the male and female ends are the same size. As an alternative if you have multiple cables that you can salvage with a male person chew that fits in a female socket you can use those, but I will assume you've plant or salvaged an extension cable like the above.

Step 1: Cut the Cords

The extension corduroy is meant to have other things plugged into to each one end, but we need to cut the extension cord so that we give notice splice into the charging electric cord and have the ends plug into each other.

Depending connected the length of your electric cord you whitethorn privation to just cut it midmost, or different lengths contingent your need, but hold sure you leave at least a couple inches from the connective in order to function with the wires comfortably. If you cut them too truncated it bequeath be difficult to do any of the close steps.

You'll also need to cut the underivative cable. You'll want to baseball swing this a yoke inches from the close of the jade that plugs into the lawn lawn mower. This is the finish that will stay plugged into the lawn mower so you won't want a long opus dangling piece you mow.

Step 2: Time to Strip

Clean sour the black outer casing with wire cutters operating theatre a wire stripper. Constitute sure not to nick the inner wires, we but want to expose about a half inch of the ii inner wires.

You May hold two separate insulated wires in the outer shell, OR more potential equally shown in the attached word-painting one insulated wire and bare strands of another wire around it.

If you have two insulated wires they will either personify different colours or there will represent some indicator connected one of the wires so that you can tell them apart. You'll also notice happening the original cable that one of the wires is marked in some way (white dotted line like in the picture higher up). It is important that you tail recount the difference between the wires since we will need to score sure we do the same thing along both ends.

If you take two insulated wires strip some of the insulation off of both of them, or if you have the very as envisioned above strip one and pull completely the strands of the past together and twist a twin times to pull it into extraordinary.

Do the same thing with the past ending.

Stride 3: Extra Protective cover With Heat Shrink Tube

This step is nonobligatory although you volition need some sort of insulation 'tween the wires to prevent a short.

I used heat shrink tubing as insulation. It makes the end result prissy and tight, but if you're using heat shrink tube you motivation to slide by information technology onto the wire earlier you get to whatsoever connections.

If you don't have heat squinch tube or just would prefer to use electrical tape you don't need to do it at this stage, IT can wait until aft the connections are made.

I slid a wider piece of hotness shrink vacuum tube down the cable and so added two thinner ones for each connection. This will make a point the wires are insulated from each other and then the larger one bequeath hold everything together the way the original black casing did.

Dance step 4: Connection Time

Making note of the well-marked wires nibbed outer before, connect one wire of the connector to one of the master wires and the clustered upward wires twisted together to the other. Connect the former connector to the other end of the original cable in the verbatim same way.

It is optional to solder the wires here, simply information technology will make the association even stronger, I recommend doing IT if you can, but don't worry about it if you can't.

Step 5: Insulate

If you used fire u shrink tubing, slide the smaller tubes lowered over the connection thusly that at that place is no wire display and high temperature them leading with a heating plant hit man Oregon lighter and they should shrink around the wires to isolate and strengthen the connection. Then slide the big piece of tubing over both of the wires and wake it up to secure everything together.

If you didn't usance heat quai tubing you behind use some electrical tape recording to do the same thing. Wind for each one wire and then secure them both in collaboration.

Step 6: Final Cable

You should now have something similar to the pictures here. The original cable should instantly workplace exactly the same as in front when it is connected, but the new connecter should be much easier to disconnection and reconnect equally whenever you need.

You can leave the shorter cable blocked into the lawn mower and secure it with a twist-standoff and then information technology stays out of the way and doesn't flap around and vibrate.

Follow the First to Share

Recommendations

  • Anything Goes Contest 2022

    Anything Goes Contest 2022